KAYA Software (General)

Questions related to KAYA Instruments software - both API and Vision Point application.

Frequently Asked Questions

  1. Building and running an API example for Acquisition mode  
  2. Building and running an API example for Generation mode  
  3. Building and running GenTL API example for Acquisition mode  
  4. Camera detection issues  
  5. Camera Discovery Delay & Command Timeout Control  
  6. Chameleon bandwidth limitiations  
  7. Chameleon configuration to run file data continuously without changing buffer content  
  8. Checking dropped packets, CRC and FEC errors in Vision Point application  
  9. CoaXPress test mode configurations  
  10. External trigger via Frame Grabber GPIO  
  11. GenICam firmware update utility for KAYA cameras  
  12. Get started with KAYA's API  
  13. How to access camera parameters from a secondary process  
  14. How to accumulate several frames/lines into a buffer using Segments Per Buffer?  
  15. How to apply Vision Point project file via external configuration KYFGLib.json  
  16. How to check hardware device ID in Windows  
  17. How to collect full diagnostic logs  
  18. How to configure KAYA's serial interface  
  19. How to configure post camera speed change timeout  
  20. How to correctly perform library exiting?  
  21. How to detect camera disconnection via API  
  22. How to downgrade Vision Point application from version 2019.1 to 4.4  
  23. How to extract camera XML file?  
  24. How to extract service logs on Windows  
  25. How to get timestamp info for a captured frame?  
  26. How to handle "first-chance" exceptions?  
  27. How to handle a resolution change  
  28. How to increase acquisition buffer count in GUI?  
  29. How to install Vision Point application on Nvidia Xavier  
  30. How to integrate with KAYA SDK and NVIDIA GPUDirect?  
  31. How to locate KAYA Instruments software logs  
  32. How to manually reinstall KAYA's driver on Windows?  
  33. How to obtain a System Information file  
  34. How to override camera XML file?  
  35. How to perform bandwidth test in Vision Point?  
  36. How to perform camera detection manually?  
  37. How to perform Dark and Flat field calibration in Vision Point  
  38. How to prevent gdb interruption on SIG44 during debug  
  39. How to record and save video buffer using Vision Point  
  40. How to reinstall KYService with a wrong path to the executable  
  41. How to reset the FG using Service Controller application?  
  42. How to reset the KAYA registry changes  
  43. How to save AVI video file larger than 4GB in Vision Point  
  44. How to save the settings to the camera  
  45. How to send X triggers from Frame Grabber to camera  
  46. How to set Debayer mode in Vision Point application?  
  47. How to set/get Camera parameters?  
  48. How to set/get Frame Grabber parameters?  
  49. How to setup JetCam to trigger mode  
  50. Insufficient memory issue on Windows 10 x 32 - Vision Point 32 bit build  
  51. KAYA's Digital Signature compatibility for Windows  
  52. LabView adaptor  
  53. Linux blocking calls and signals in the streaming thread  
  54. Linux crash handler  
  55. PCO Camware software is not compatible with Vision Point 2019.2 and above  
  56. Performing a camera reset  
  57. Performing a Frame Grabber reset  
  58. PoCXP automatic management  
  59. PoCXP automatic management troubleshooting  
  60. Secure Boot and DKMS Driver Signature  
  61. Streampix NpxKaya.dll registration  
  62. Streampix 7 download  
  63. Transition to the new kernel driver starting from software 4.4  
  64. Trigger Configuration  
  65. Troubleshoot KAYA service  
  66. Uninstalling Vision Point on Linux  
  67. Unsupported hardware issue for Windows 7 OS and Vision Point 2019.1 version  
  68. Updating KAYA PCI device firmware using pre-built utility for Linux  
  69. Updating KAYA PCI device firmware using pre-built utility for Windows  
  70. Updating KAYA PCI device firmware using Vision Point Application  
  71. Upgrading KAYA Instruments' old Hardware and Software using utility for Windows  
  72. Using Frame Grabber with Halcon application  
  73. Using Trigger Mode in Chameleon Simulator  
  74. Using Trigger Mode in Vision Point Application  
  75. Vision Point 2019.1 firmware versioning capability  
  76. Vision Point documentation folder location  
  77. Vision Point usage with Docker for early adopters  
  78. Working with CoaXPress Frame Grabber and Chameleon Camera Simulator  
Help Topics
Techical Support

Please Wait!

Please wait... it will take a second!